Is your LG washer flashing the dreaded FE error code? If so, you’re not alone — many LG front load washers show this code when there’s a water overflow or drainage problem.
You might feel frustrated or unsure about what to do next, but don’t worry. This guide will walk you through simple steps you can take right now to fix the FE error yourself. From resetting your machine to checking filters and hoses, you’ll learn how to troubleshoot common causes before calling a technician.
Keep reading, and you’ll have your washer running smoothly again in no time.
Credit: www.youtube.com
What Fe Code Means
The FE code on an LG washer signals a water level issue. It usually means the washer detects too much water inside. This error stops the washing cycle to avoid overflow and damage.
Knowing the FE code helps you fix the problem quickly. It often points to a sensor or drainage problem. Understanding its meaning can save time and avoid costly repairs.
What Causes The Fe Code?
The FE code appears if the washer overfills with water. Possible causes include a blocked drain pump filter. Dirty or clogged inlet hose filters can also trigger it.
Another reason is a faulty water level sensor or a blocked pressure sensor hose. These parts help the washer check water levels accurately. If they fail, the washer may think it has too much water.
How To Reset The Fe Code
Start by unplugging the washer to reset the control board. This step clears the error temporarily. Next, drain any water left inside the tub manually or by using a drain cycle.
Run a short cycle without detergent to check for excess suds. Too many suds can confuse the water level sensor. Using a high-efficiency (HE) detergent helps prevent this issue.
If the FE code stays after cleaning and resetting, professional help is needed. Problems like a broken water inlet valve or a faulty water level sensor may require repair. A technician can test and replace these parts safely.
Initial Reset Steps
The LG washer displaying the FE error code signals a water overflow issue. Starting with initial reset steps can often clear this error. These steps help reset the washer’s control system and remove minor blockages. Follow these simple actions before calling a technician.
Unplug And Power Reset
First, unplug the washer from the electrical outlet. This cuts power completely and resets the control board. Wait for about five minutes to allow the machine to fully reset. Then, plug the washer back in and turn it on. This simple step often clears error codes caused by temporary glitches.
Manual Water Drain
Check if water remains inside the drum. If yes, drain it manually to avoid further issues. Locate the drain pump filter at the bottom front panel. Open the panel carefully and use a shallow container to catch water. Remove debris from the filter to improve drainage. This clears blockages that might cause the FE error.
Run No-detergent Cycle
Run a short wash cycle without detergent. Excess soap suds can confuse the water level sensor and cause errors. Using no detergent flushes out leftover suds and resets the sensor. Make sure to use high-efficiency detergent in future washes to prevent soap buildup.
Check Drain Pump Filter
The LG washer code FE often signals a problem with water overflow or drainage. One common cause is a clogged drain pump filter. Checking this filter helps your washer drain water properly and stops the error code from appearing.
Cleaning the drain pump filter is a simple task that can save time and money. It prevents water buildup and keeps your washer working smoothly. Follow these steps to locate and clean the filter safely.
Locate The Filter
Start by unplugging your washer for safety. The drain pump filter is usually behind a small access panel at the front bottom of the washer.
Open this panel carefully using a flat tool or your fingers. Inside, you will see a round filter cover. This is the drain pump filter.
Keep a towel or shallow container nearby. Some water may spill out when you open the filter.
Clean Debris And Residue
Turn the filter cover counterclockwise to remove it. Take out the filter and check for lint, coins, or other debris.
Rinse the filter under running water to remove all dirt and residue. Clear out the filter housing inside the washer as well.
Once clean, put the filter back in and twist it clockwise to secure it. Close the access panel tightly before plugging the washer back in.
Inspect Water Inlet System
Inspecting the water inlet system is essential when your LG washer shows the FE error code. This code often signals problems with water filling or overflow. Checking the water inlet helps find blockages or faulty parts. It ensures water flows correctly into the machine. Proper inspection can save time and avoid costly repairs.
Clean Inlet Hose Filters
The inlet hose filters catch dirt and debris from the water supply. Over time, these filters can clog and restrict water flow. Turn off the water supply before removing the hoses. Carefully detach the hoses from the washer and faucet. Look inside the filter screens for dirt buildup. Use a soft brush or cloth to clean the filters. Rinse with water until clean. Reattach the hoses tightly to avoid leaks. Clean filters help maintain proper water flow and prevent the FE error.
Examine Water Inlet Valve
The water inlet valve controls the flow of water into the washer. A faulty valve may cause overfilling or no water entry, triggering the FE error. Unplug the washer before checking the valve for safety. Inspect the valve for signs of damage or wear. Listen for unusual sounds when the washer fills. Test the valve with a multimeter to check electrical continuity. If the valve is defective, replacing it is necessary. A good valve ensures correct water levels during each wash cycle.
Examine Pressure Sensor Hose
The pressure sensor hose plays a key role in your LG washer’s water level detection. This small hose connects the tub to the pressure sensor. It helps the machine know how much water is inside. Problems with this hose often cause the FE error code. Examining the pressure sensor hose can fix this issue. Follow these simple steps to check it carefully.
Check For Blockages
Start by locating the pressure sensor hose. It is usually near the bottom of the washer. Remove the hose gently from the sensor and the tub. Look inside the hose for any dirt, lint, or debris. Even small blockages can stop water flow. Blow air through the hose to clear any clogs. Make sure water can pass freely without resistance. A clean hose helps the sensor work properly.
Test Hose Integrity
Inspect the hose for cracks or holes. A damaged hose can cause false water level readings. Check if the hose feels soft or brittle in places. Replace the hose if you see any damage. Also, ensure the hose fits tightly on both ends. Loose connections can let air leak, causing errors. Use a new hose if needed to avoid future problems.
Credit: www.lg.com
Use Diagnostic Mode
Using the diagnostic mode on your LG washer helps find the exact cause of the FE error. This mode runs tests on the machine’s parts and shows error codes. These codes help you understand what needs fixing. Diagnostic mode saves time and avoids guesswork. It is a useful step before calling a technician. Follow the steps below to activate and use this mode effectively.
Activate Service Cycle
First, make sure the washer is off. Press and hold the “Spin” and “Soil Level” buttons at the same time. While holding them, press the “Power” button to turn on the washer. Keep holding the buttons until the display shows “t01” or similar code. This means the service cycle is active.
Use the “Spin” button to scroll through different test cycles. Each cycle checks a specific part, like the water valve or motor. Press the “Start/Pause” button to begin the selected test. The washer will run the test and then stop automatically.
Interpret Error Codes
During the service cycle, the washer may display error codes. These codes give clues about the problem. For example, “FE” means there is a water overflow or leak issue. Other codes like “dE” or “UE” show door or unbalanced load problems.
Write down the codes shown. Use the LG user manual or online resources to find what each code means. Knowing the exact error helps you decide if you can fix it yourself or need professional help. Diagnostic mode gives clear guidance on the washer’s condition.
When To Call A Technician
Knowing the right time to call a technician for your LG washer with Code FE is important. Some fixes you can try yourself. Other problems need professional tools and skills. Calling a technician helps avoid further damage and costly repairs. Below are key issues where expert help is needed.
Water Inlet Valve Replacement
The water inlet valve controls water flow into the washer. If it is faulty, the washer may overfill or not fill at all. A broken valve causes the FE error code to appear. Replacing this valve is tricky and requires technical knowledge. A technician can test the valve and replace it safely.
Pressure Sensor Or Water Level Sensor Repair
The pressure sensor detects the water level inside the drum. A blocked or broken sensor causes wrong water readings. This leads to the FE error and washing problems. Repairing or replacing the sensor needs special tools. A technician can clean, fix, or replace the sensor properly.
Control Board Inspection
The control board manages all washer functions. A damaged board can send wrong signals, causing error codes. Diagnosing control board issues requires expert testing. A technician can inspect the board and repair or replace it. This ensures your washer works reliably again.
Preventing Future Fe Errors
Preventing future FE errors on your LG washer saves time and hassle. These errors often happen because of water overflow or sensor problems. Small steps help avoid them. Proper detergent use, regular filter cleaning, and correct hose positioning keep your washer running smoothly.
Use He Detergent Only
Use only HE (high-efficiency) detergent in your LG washer. Regular detergents create too many suds. Excess suds confuse the water level sensor. This can trigger the FE error code. HE detergents produce fewer suds and clean better. Always follow the detergent amount suggested in the manual.
Regular Filter Cleaning
Clean the drain pump filter regularly. Dirt and lint block water flow. This causes the washer to overflow or stop draining. The filter is behind a small panel at the washer’s bottom. Open it carefully and remove debris. Cleaning the filter helps avoid many common FE error causes.
Maintain Proper Hose Positioning
Check the inlet hoses often for proper placement. Hoses that are bent or kinked block water flow. Blocked hoses cause wrong water levels and trigger FE errors. Make sure hoses are straight and firmly connected. Secure them to avoid movement during washing cycles.
Credit: www.lg.com
Frequently Asked Questions
How To Fix Fe Error In Lg Washing Machine?
Unplug and reset the LG washer. Clean drain pump filter and inlet hose filters. Check pressure sensor hose for clogs. Use HE detergent only. If error persists, call a technician to inspect the water inlet valve or sensor.
What Does Fe Mean On A Washer Machine?
FE on a washer means a water overflow or leak error. It signals drainage or water level sensor issues.
How Do I Reset The Error Code On My Lg Washer?
Unplug your LG washer to reset the control board. Clean the drain pump filter and inlet hose filters. Check for clogs or kinks in the pressure sensor hose. Run a drain/spin cycle with no detergent. If the error persists, contact a technician for further diagnosis.
What Does Fe Error Mean?
FE error on an LG washer means water overflows or leaks. It signals a drainage or water inlet problem needing inspection or cleaning.
What Does Lg Washer Code Fe Mean?
FE means the washer detects a water overflow or drainage problem.
Conclusion
The LG Washer Code FE signals a water overflow issue. Start by unplugging and resetting your washer. Check and clean the drain pump filter and inlet hose filters. Use the right detergent to avoid excess suds. Inspect the pressure sensor hose for blockages.
Run a diagnostic cycle if your model supports it. Persistent errors often mean a faulty part. In that case, seek professional help to avoid damage. Following these steps can save time and prevent bigger problems. Stay calm and tackle the FE code carefully.